In this article, we will guide you on how to fix different HP printer flashing E error codes.
Do the following solutions we provide in this article based on the error code you received to solve your HP printer problem.
Table of Contents
Why Is My HP Printer Flashing E0 [Answer & Solution] – HP Printer Flashing E Error Codes
Your HP printer is displaying an E0 error code because one or more of its ink cartridges is incompatible, missing, damaged, incorrectly installed, or faulty.
Depending on the reason for the error, you may have to reinstall the cartridge, clean its contacts, or replace the cartridge altogether.
The ink cartridge below is compatible with the following HP printers: HP OfficeJet 8600, OfficeJet Pro 251dw, 276dw, 8100, 8610, 8620, and 8630 Series.
Why is MY HP Printer Flashing E2 or E1 [Answer & Solutions] – HP Printer Flashing E Error Codes
Your HP printer will flash or display an E2 or E1 error code if the loaded paper size and the size setting don’t match.
When this happens, you have to either adjust the paper size setting to match the size loaded or put papers that matches the size in the setting.
This article: HP Printer Errors and Solutions [Detailed] covers a wide range of other HP printer errors that we didn’t discuss in this article.
How to Fix HP Printer Flashing E3 – HP Printer Flashing E Error Codes
An E3 code is an indication of a carriage jam. To solve this problem, do the following:
1. Check Your Machine’s Carriage Path for Obstructions
How to Check HP Printer Carriage Path for Obstructions
Do the following steps to check your HP printer carriage path for obstructions:
Step 1: Ensure the printer is turned on, and then detach the power cable from the machine.
Step 2: For printers with batteries, take out the battery at this point.
Step 3: Lift or open the machine’s carriage door so you can get to the carriage.
Step 4: Check the path to see if debris like dislodged labels or any crumpled paper is blocking it. If you find any debris, ensure to take them out completely.
Step 5: Ensure the carriage’s latch is properly closed (if yours has a latch).
Step 6: Now, try moving the carriage from the left to the right. Ensure it is moving freely. If it isn’t, then continue with the troubleshooting.
Step 7: Shut the door, plug the power cable into the printer then switch it back on.
2. Reset Your Printer
To reset your printer, click this link: HP Printer Flashing [Issues & Solutions] – How to Reset HP Printer, and then follow the steps in the “How to Reset HP Printer” section.
If the problem persists after the reset is complete, then contact HP Support for further assistance.
How to Fix HP Printer Flashing E4 – HP Printer Flashing E Error Codes
An e4 error code means there is a paper jam issue. Do the solutions below to solve the error.
1. Remove the Jam Automatically
To remove the jam automatically, simply press your cancel key. If this doesn’t solve the problem, go to the next solution.
2. Remove the Jam Manually
There are several places in the printer where a paper jam can happen in. Do the following steps to remove paper jams in these places.
i. Cartridge Access
How to Manually Remove Paper Jam in HP Printer Cartridge Access
Do these steps to manually remove a paper jam from your HP printer cartridge access:
Step 1: If necessary, push the printer’s output tray in.
Step 2: Raise the cartridge door.
Step 3: Wait for some seconds for the carriage to become silent and idle.
Step 4: Ensure the printer is turned on and then detach the power cable from the machine. If you do not disconnect the cord before you reach into the printer, you may receive an electric shock or get injured.
Step 5: Now, check the cartridge access space to see if any object is stuck there. Move the carriage back and forth to check this.
Step 6: Behind the access area, you will find a paper path cover.
Step 7: Pinch the two tabs together then lift. This would remove the path cover.
Step 8: Check inside the machine for jammed paper. If you find any, grab the paper with your hands and firmly but slowly pull it towards you.
Step 9: Check the duplex rollers for a flip gate, using your fingers, lift it.
Step 10: Now, also check underneath this gate for jammed papers.
Step 11: Return the gate to its position by pressing it down. Ensure it snaps in place.
Step 12: Also, put your paper path cover in its position and ensure it is seated well. To do this, pinch the two tabs together, then slide the path cover back, press it down and ensure it locks in place.
Step 13: Close the cartridge door. If it refuses to close fully, then you did not properly insert the paper path cover.
Step 14: Pull your output tray then raise the tray extender.
Step 15: Connect the power cable back to the printer, then turn it back on.
Do a print job to see if the paper jam error has been fixed.
ii. Cleanout and Input Tray Areas
How to Manually Remove Paper Jam in HP Printer Cleanout and Input Tray Areas
Do these steps to manually remove a paper jam from your HP printer cleanout and input tray areas:
Step 1: Lift or open the printer’s input tray.
Step 2: Pull the output tray then remove the papers in the tray.
Step 3: Check inside the area for any stuck paper or item. Make use of a flashlight if you can’t see the inside well.
Step 4: Switch the printer off, and disconnect cords attached to it like a USB cable. Disconnect the power cable from the printer as well.
Step 5: Hold the printer’s top firmly and then turn it sideways. To get access to the cleanout, pull your input tray.
Step 6: To get a better view of the area, tilt the machine down 10-20 degrees. Now check for debris or stuck paper. If any is found, pull it out, do this gently so the paper doesn’t tear.
Step 7: Check the pickup rollers for torn paper. If you find any, is found, remove them.
Step 8: Put the printer back in its usual position.
Step 9: Load paper into the paper tray.
Print any document to see if the problem has been resolved.
This article: HP Printer Flashing [Issues & Solutions] will guide you on how to solve a wide range of HP printer flashing issues.
Check out this HP multipurpose printer paper below.
iii. Document Feeder
How to Manually Remove Paper Jam in HP Printer Document Feeder
Do these steps to manually remove a paper jam from your HP printer document feeder:
Step 1: Lift the document feeder cover.
Step 2: Check for and pull out any stuck paper in the rollers. The paper can get torn while you’re removing it, in which case, you need to check the wheels and rollers for paper pieces. If remnants are not removed, it may cause paper jam errors down the road.
Step 3: Close the cover by pressing it down; ensure it snaps in place.
Step 4: Press your cancel key to erase the error.
Print any document to see if the problem has been solved. If it hasn’t, then do the next solution.
Watch this instructional video for more information on how to manually remove a paper jam from your HP printer.
3. Clean Your Paper Feed Rollers
If debris such as paper fiber or dust builds upon and around the printer’s paper feed rollers, it may result in a paper jam issue.
To solve the issue, you need to clean the areas where debris can collect.
I. Cartridge Access Rollers
How to Clean HP Printer Cartridge Access Rollers
Do the steps below to clean your HP printer cartridge access rollers:
Step 1: Switch the printer off, then disconnect its power cable.
Step 2: If necessary, push the printer’s output tray in.
Step 3: Raise the cartridge door.
Step 4: Get a clean cloth (ensure it is lint-free), then lightly dampen it with water. Squeeze the cloth to remove excess liquid.
Step 5: Place the dampened cloth on the rollers and press it. Use your fingers to roll the rollers. You can apply more pressure (don’t use too much pressure) to clean off dirt or dust buildup.
Step 6: Wait for some minutes (between 10-15 minutes) so the rollers can get dry.
Step 7: Behind the access area, you will find a paper path cover.
Step 8: Pinch the two tabs together then lift. This would remove the path cover.
Step 9: Repeat steps 4 to 6 for the paper path area.
Step 10: Once the rollers are completely dry, put your paper path cover back in its position. . To do this, pinch the two tabs together, then slide the path cover back, press it down and ensure it locks in place.
Step 11: Close the cartridge door.
Step 12: Plug the power cable back into the printer, then turn it back on.
Print any document to see if the problem has been resolved. If it hasn’t, continue to the next area.
ii. The Rollers under The Machine
How to Locate the Rollers under your HP Printer and Clean them
Do the steps below to locate the Rollers under your HP printer and clean them:
Step 1: Switch the printer off, then disconnect its power cable.
Step 2: Draw out your input tray, then remove the papers in it.
Step 3: Hold the printer’s top firmly, and then turn it sideways to get access to the rollers.
Step 4: Get a clean cloth (ensure it is lint-free), then lightly dampen it with water. Squeeze the cloth to remove excess liquid.
Step 5: Place the dampened cloth on the rollers and press it. Use your fingers to roll the rollers. You can apply more pressure (don’t use too much pressure) to clean off dirt or dust buildup.
Step 6: Wait for about 10 minutes so the rollers can get dry.
Step 7: Slide your input tray back in and put the printer in an upright position.
Step 8: Plug the power cable back into the printer, then turn it back on.
Print any document to see if the problem has been resolved. If it hasn’t, continue to the next area.
iii. The ADF Rollers
How to Clean HP Printer ADF Rollers
Do the steps below to clean your HP printer ADF rollers:
Step 1: Raise your printer’s ADF cover.
Step 2: Check inside for any obstructions. Ensure nothing is blocking the engagement between the rollers and paper. Check properly as even the smallest paper piece can result in a paper feed problem.
Step 3: Get a clean cloth (ensure it is lint-free) then lightly dampen it with water. Squeeze the cloth to remove excess liquid.
Step 4: Use the dampened cloth to clean the separator pad and rollers.
Step 5: Wait for about 10 minutes so the rollers can get dry.
Step 6: Close your ADF cover.
Print any document to see if the problem has been resolved. If it hasn’t, continue to the next solution.
4. Reset Your Printer
If the problem persists, then it may be a false error, meaning no paper is stuck anywhere. In this case, you have to reset your printer.
To reset your printer, click this link: HP Printer Flashing [Issues & Solutions] – How to Reset HP Printer, and then follow the steps in the “How to Reset HP Printer” section.
If the problem persists after you have done all the solutions discussed, then you have to call HP Support for further assistance.
Check out this HP Color LaserJet Pro M479fdn Printer below if your printer is old and you would rather buy a new one instead of servicing the old one.
How to Fix HP Printer Flashing E5 – HP Printer Flashing E Error Codes
An e5 error code indicates an error state in the printer’s scanner. This error will not disrupt printing as only the scanner is affected.
To reset your printer, click this link: HP Printer Flashing [Issues & Solutions] – How to Reset HP Printer, and then follow the steps in the “How to Reset HP Printer” section.
If resetting the printer doesn’t resolve the error, then the printer has to be serviced. In which case, contact HP Support for further assistance.
How to Fix HP Printer Flashing E6 – HP Printer Flashing E Error Codes
You will get an e6 error code when your printer has a general issue.
You have to reset your printer to clear this error. To reset your printer, click this link: HP Printer Flashing [Issues & Solutions] – How to Reset HP Printer, and then follow the steps in the “How to Reset HP Printer” section.
Ensure your printer is connected directly to your electrical socket rather than a surge suppressor or power strip. If the problem doesn’t get resolved, then try another socket.
If the issue isn’t resolved after you do the above, then the printer has to be serviced. In which case, contact HP Support for further assistance.
How to Fix HP Printer Flashing E9 – HP Printer Flashing E Error Codes
An e9 error code means a problem was encountered when the printer firmware was being updated.
How to Fix HP Printer E9 Error
Do the solutions below to fix the HP printer e9 error:
1. Redo your Wireless Setup
How to Do a Wireless Setup on HP Printer
Do the steps below to set up your HP printer wireless connection:
Step 1: Ensure your computer and router are switched on. Ensure the computer is also linked to the wireless network that you wish to connect your printer to.
Step 2: If you are yet to set up your printer, then do this: Turn the printer on, put in the inks, and load the paper tray. Also, ensure the printer is within the router range, it should also be near the computer.
Step 3: You can secure the connection in three different ways; with HP Smart, WPS, and Wi-Fi Direct.
With WPS
Some routers don’t support WPS. So, if yours doesn’t, simply skip this and go to HP Smart.
Step 1: Press your printer’s power and wireless buttons simultaneously and hold on to them for about 3 seconds.
Step 2: Check your router for the WPS key. Now, press this button and on to it for about 3-5 seconds. The connection process should get started.
Note: Your printer will search for available connections for 2 minutes after you press the wireless key. If you don’t press your router’s WPS key at this time, you would have to redo the steps to secure the connection.
Once the connection is secured, your printer’s Wireless light will become solid.
With HP Smart
Step 1: Download the HP Smart from your App Store or Microsoft Store, depending on your system type. Next, install it.
Step 2: Press your printer’s wireless key and hold on to it for about 3 seconds.
Step 3: Open HP Smart on the computer. Now, click on the Plus symbol. The tool will start searching for available printers on the network.
Step 4: Pick your printer from the list of available printers then “Continue”.
Step 5: You will be asked to type in the network password (WPA key or WEP).
Step 6: Once the connection is complete, click on “Continue” then “Exit Setup”.
Wi-Fi Direct
Use this option when the network is a guest one.
Step 1: Turn on the Wi-Fi Direct by touching the following buttons: Information, Cancel, and Resume.
Step 2: Open the settings of your computer’s Wi-Fi and then choose the printer.
You can read this detailed guide on How to Connect HP printer for more information.
2. Press Your Printer’s Information Key
If the printer prints the information page, then the problem has been fixed. If it doesn’t, then the printer is in its recovery mode.
When this happens, your printer will automatically re-download the firmware. The time with which it would do this is based on the speed of your network. However, 2 hours should be enough for the download to get complete.
Note: The solutions above apply to the following HP printer models: HP Deskjet 3630, HP Deskjet 3700, and HP envy 6000.