In this article, we will discuss the meaning of HP printer warning lights on HP LaserJet Pro M130 and Ultra M134 printers and how to clear the warning lights.
Note: The guide below is for HP LaserJet Ultra MFP 134a, LaserJet Pro MFP M130a, and M132a printers.
Er/01 is Displayed and Blinking Attention Light – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
This error message and HP printer warning light pattern shows that your printer’s input tray is out of paper. Therefore, to fix this error, you need to reload your printer with paper.
How to Load the Input Tray of HP LaserJet Pro, Ultra M130 – M134 Printers with Paper – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To load your printer’s input tray with paper, do the following steps:
Step 1: Lift your printer’s dust cover.
Step 2: Adjust the paper width and length guides to their extreme positions.
Step 3: Load your printer’s input tray with plain paper with the print side face up.
Note: Do not load more than 150 paper sheets into the input tray. Ensure that the print side faces up while the top edge goes into the printer. if the paper you are loading is pre-punched, the side with holes should be at the tray’s left side when you load it in.
Step 4: Push the paper stack into the printer’s input tray.
Step 5: Adjust the paper width and length guides to rest against the paper stack.
Step 6: Lightly press the side of the printer’s dust cover inwards.
Step 7: Lower the printer’s dust cover.
Caution: Don’t lower the printer’s dust cover if you are not pressing the sides inwards. Doing otherwise might get the printer or the dust cover damaged.
Note: Before you print or copy, you need to choose the correct paper type and paper size settings from your computer or printer’s control panel.
If the issue is not resolved after doing the above steps, then you need to service your printer.
How to Service HP LaserJet Pro, Ultra M130 – M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To service your printer, contact HP Customer Support to fix a repair date for your printer. Folks living in the Asia Pacific are usually told to go to the nearest local service center.
The repair is free for printers under warranty. Also, if the printer cannot be repaired, a replacement will be given free of charge for printers still under warranty.
On the other hand, if your printer is out of warranty, you will pay for the repair and also for the replacement printer.
You can check the warranty status of your printer here.
Er/02 is Displayed and Blinking Attention Light – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
This error message and HP printer warning light pattern shows that your printer’s top cover is open or not properly closed. To fix this error, you need to properly close the top cover and also lower your printer’s scanner assembly.
Check if the error message and the blinking attention light are cleared after doing the instructions above.
If the issue is not resolved after doing the above steps, then you need to service your printer.
To service your printer, follow the instructions we shared under the “How to Service HP LaserJet Pro, Ultra M130 – M134 Printers” section of this article.
Er/03 is Displayed and Blinking Attention Light – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
This error message and HP printer warning light pattern shows that your printer was unable to pick up a sheet of paper. As a result, the print job was not printed.
The printer might either be unable to pick paper from the automatic document feeder or the input tray. We have provided troubleshooting tasks below for both scenarios.
HP LaserJet Pro, Ultra M130 – M134 Printers not Picking Paper from Input Tray [Fixed] – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
If your printer is not picking paper from its input tray, do the following tasks to resolve this problem.
1. Confirm that you are Using Genuine HP Cartridges – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
Although you can use other cartridges in HP printers; however, to get the best result, it is recommended that you use genuine HP cartridges rather than refilled or non-HP cartridges. HP as a company does not guarantee the reliability or quality of such supplies.
Also, if you are using a non-HP toner cartridge, the tasks we provide below might not fix your printer’s problem as they are proven to work with HP cartridges.
If you are not sure of your cartridges’ authenticity, you can check this webpage to find out.
If the cartridge is not genuine, we recommend that you get a replacement cartridge from a reputable store or the HP store.
After installing genuine HP cartridges, check if the issue is resolved.
If the issue is not resolved, do the task below.
2. Examine the Loaded Paper, and then Reload it into your printer – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
Your printer’s problem might be because the paper in use is bent, wrinkled, curled, dusty, or ripped. Apart from these poor paper conditions, the paper quality also determines whether the printer will be free from paper feed issues or not.
Here are some guidelines you ought to bear in mind that will help to prevent future paper feed issues:
i. Use quality paper that matches the specifications of your printer.
ii. Don’t store paper in a humid environment; always store your paper in a place that is dry and cool.
iii. Do not load your printer with already-used paper; that is, paper that has been printed on already. Such paper can get stuck to other paper within the paper stack.
iv. Always allow your printer to finish a print job before you reload the paper into the print tray, or only reload paper when you see any of these messages: “Load Paper” or “Out of Paper.”
To examine the loaded paper, and then reload it into your printer’s input tray, do the following steps:
Step 1: Lift your printer’s dust cover.
Step 2: Take out the stack of paper from your printer’s input tray.
Step 3: Examine the stack of paper and confirm that the condition of each paper sheet is good. If you find any sheet that is torn, wrinkled, or bent, remove it from the paper stack.
Step 4: Hold the stack of paper in both hands, and then flex it in a way that a “U” shape is formed.
Step 5: Flex the stack of paper in the other direction still forming a “U” shape.
Flexing the stack of paper in this manner can loosen the individual sheets within the stack.
Step 6: Load the paper stack with the print side face up into your printer’s input tray.
Note: Do not load more than 150 paper sheets into the input tray. Ensure that the print side faces up while the top edge goes into the printer. if the paper you are loading is pre-punched, the side with holes should be at the tray’s left side when you load it in.
Step 7: Push the paper stack into your printer’s input tray.
Step 8: Adjust the paper width and length guides to rest against the paper stack.
Step 9: Lightly press the side of the printer’s dust cover inwards.
Step 10: Lower the printer’s dust cover.
Caution: Don’t lower the printer’s dust cover if you are not pressing the sides inwards. Doing otherwise might get the printer or the dust cover damaged.
Note: Before you print or copy, you need to choose the correct paper type and paper size settings from your computer or printer’s control panel.
Try printing a document.
If the issue is not resolved, do the task below.
3. Check and Change the Paper Type and Paper Size Settings – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
The paper type and paper size settings in the program you are printing from might be responsible for the “Out of Paper” message that is displayed even though the input tray has paper.
Therefore, to fix this issue, check and change the settings if need be.
How to Check and Change Paper Type and Paper Size Settings on HP Printers that have LCD Icon Display
Follow the steps below depending on your computer’s operating system.
Windows
Step 1: Open the program you want to print from.
Step 2: Click on “File.”
Step 3: Click on “Print.”
This action will open the Print window.
Step 4: Open the dialog box for “Properties.”
This option might be labeled as “Properties,” “Printer Setup,” “Printer,” “Preferences,” or “Options” depending on the program you are using.
Step 5: Click on the tab labeled “Paper/Quality.”
Step 6: From the drop-down menu for “Media,” choose the correct paper type.
Step 8: Click on “Advanced.”
Step 9: Choose the correct paper size from the drop-down menu.
Step 10: Click on “OK.”
Step 11: Click on “OK” to apply the new settings.
Step 12: Click on “Print.”
Mac
Step 1: Open the document you want to print on your Mac.
Step 2: Click on “File.”
Step 3: Click on “Print.”
Step 4: Ensure that you select your printer.
Step 5: If the print dialog box doesn’t have options, click on “Show Details.”
Step 6: From the drop-down menu for “Paper Size,” choose the correct paper size.
Step 7: Choose the “Media & Quality” or “Paper Type/Quality” menu.
Step 8: Choose the correct paper type.
Step 9: Click on “Print.”
How to Check and Change Paper Type and Paper Size Settings on HP Printers that have 2-line Display
To change the input tray settings via the control panel, do the following steps:
Step 1: Press your printer’s setup button.
Step 2: Press your printer’s right arrow button until you see “System Setup.”
Step 3: Press your printer’s “OK” button.
Step 4: Press your printer’s right arrow button until you see “Page Setup.”
Step 5: Press your printer’s “OK” button.
Step 6: Press your printer’s right arrow button until you see “Paper Type.”
Step 7: Press your printer’s “OK” button.
Step 8: Press your printer’s right arrow button to choose the correct paper type.
Step 9: Press your printer’s “OK” button.
Step 10: Press your printer’s right arrow button until you see “Paper Size.”
Step 11: Press your printer’s “OK” button.
Step 12: Press your printer’s right arrow button to choose the correct paper size.
Step 13: Press your printer’s “OK” button.
How to Check and Change Paper Type and Paper Size Settings on HP Printers that have a Touchscreen Display
To change the input tray settings via the control panel, do the following steps:
Step 1: Swipe left from your printer’s control panel home screen.
Step 2: Touch the “Setup” option.
Step 3: Touch the “System Setup” option.
Step 4: Touch the “Paper Setup” option.
Step 5: Touch the “Paper Type” option.
Step 6: Choose the correct paper type.
Step 7: Touch the “Paper Size” option.
Step 8: Choose the correct paper size.
Try printing a document.
If the issue is not resolved, do the task below.
4. Clean your Printer’s Paper Feed and Pick Rollers by Printing a Cleaning Page – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
When debris, paper fiber, or dust builds up on your printer’s paper feed and pick rollers, it might lead to paper feed issues and paper jams. You can get rid of this buildup by printing a cleaning page.
How to Clean Paper Feed and Pick Rollers by Printing a Cleaning Page on HP Printers that have an LCD icon Display
Do the steps below to print a cleaning page:
Step 1: Run a Windows search on your computer for the model of your printer.
Step 2: From the search results, click on the name of your printer.
This action will open the HP Printer Assistant.
Step 3: Click on “Print.”
Step 4: Click on “HP Device Toolbox.”
Step 5: Click on the tab labeled “System.”
Step 6: Choose the “Service” page.
Step 7: Click on “Start” from the “Cleaning Mode” area.
Your printer will start the process of cleaning the paper feed and pick rollers.
How to Clean Paper Feed and Pick Rollers by Printing a Cleaning Page on HP Printers that have 2-Line Display
Do the steps below to print a cleaning page:
Step 1: Press your printer’s setup button on the control panel.
Step 2: Press your printer’s right arrow button until you see “Service.”
Step 3: Press your printer’s “OK” button.
Step 4: Press your printer’s right arrow button until you see “Cleaning Page.”
Step 5: Press your printer’s “OK” button.
Step 6: When you get the prompt, load your printer’s input tray with regular white paper.
Step 7: Press your printer’s “OK” button.
Your printer will start the process of cleaning the paper feed and pick rollers.
How to Clean Paper Feed and Pick Rollers by Printing a Cleaning Page on HP Printers that have Touchscreen Display
Do the steps below to print a cleaning page:
Step 1: From your printer’s control panel home screen, touch the “Setup” option.
Step 2: Touch the “Service” option.
Step 3: Touch the “Cleaning Page” option.
Step 4: When you get the prompt, load your printer’s input tray with regular white paper.
Step 5: Press your printer’s “OK” button.
Your printer will start the process of cleaning the paper feed and pick rollers.
Try printing a document.
If the issue is not resolved, do the task below.
5. Manually Clean Pickup Roller of HP LaserJet Pro, Ultra M130 – M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To manually clean your printer’s pickup rollers, do the following steps:
Step 1: Get these items:
i. Fluff-free fabric or swab.
ii. Distilled, bottled, or filtered water (Do not use tap water as the contaminants in it might damage your printer).
step 2: Turn off your printer.
step 3: Remove the power cable from your printer.
step 4: Wait for your printer to get cool before you proceed.
Step 5: Lift your printer’s scanner assembly.
Step 6: Open your printer’s top cover.
Step 7: Take out the toner cartridge from your printer.
Step 8: Take out the imaging drum from your printer.
Step 9: Locate the pickup roller within your printer.
Step 10: Moisten the fabric or swab with distilled, bottled, or filter water.
Step 11: Squeeze the fabric or swab to remove excess liquid.
Step 12: Clean your printer’s pickup roller with the moistened fabric or swab.
Ensure that you apply a bit of pressure to remove the buildup of dirt, dust, debris, etc.
Step 13: Wait for the rollers to get completely dry before you proceed.
You might have to wait for 10 minutes.
Step 14: Reinsert the toner cartridge into your printer.
Step 15: Reinsert the imaging drum into your printer.
Step 16: Close your printer’s print cartridge door.
Step 17: Plug the power cable into your printer.
Step 18: Turn on your printer.
Try printing a document.
If the issue is not resolved, do the task below.
6. Reset HP LaserJet Pro, Ultra M130 – M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To reset your printer, do the following steps:
Step 1: Turn on your HP printer if it is turned off.
Step 2: Remove the power cable from your HP printer.
Step 3: Remove the power cable from the wall outlet.
Step 4: Wait for 60 seconds.
Step 5: Reconnect your power cable to the outlet.
Note: Your printer should be plugged directly into an electrical wall outlet instead of other power sources according to HP’s recommendation.
Step 6: Plug the power cable into your printer.
Step 7: Turn on your HP printer.
You can read this article: How to Reset HP Printer [Detailed Guide] to learn about other resets that you can perform on your HP printer.
Try printing a document.
If the issue is not resolved, you need to service your printer.
To service your printer, follow the instructions we shared under the “How to Service HP LaserJet Pro, Ultra M130 – M134 Printers” section of this article.
HP LaserJet Pro, Ultra M130 – M134 Printers not Picking Paper from ADF [Fixed] – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
If your printer is not picking paper from its ADF, do the following tasks to resolve this problem.
1. Clean ADF Rollers and Separator Pad of HP LaserJet Pro, Ultra M130 – M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To clean your printer’s ADF rollers and separator pad, follow the steps below.
Step 1: Get these items:
i. Fluff-free fabric or swab.
ii. Distilled, bottled, or filtered water (Do not use tap water as the contaminants in it might damage your printer).
Step 2: Take out the original document from your printer’s ADF.
Step 3: Turn off your printer.
Step 4: Remove the power cable from your printer.
Step 5: Open your printer’s ADF cover.
Step 6: Locate the paper pick rollers and separator pad within your printer’s ADF.
Step 7: Moisten the fabric or swab with distilled, bottled, or filter water.
Step 10: Squeeze the fabric or swab to remove excess liquid.
Step 12: Clean the ADF pick roller and separator pad with the moistened fabric or swab to remove residue on these printer parts.
Step 13: Allow the ADF cover to remain open for two minutes to enable the pick rollers and separator pad to get dry.
Step 14: Close your printer’s ADF cover.
Step 15: Reload your printer’s ADF tray with the original document with the print side facing up.
Note: The ADF cannot take above 35 pages at once. Therefore, don’t load the ADF with paper sheets that exceed this number. Doping so can lead to all kinds of pick problems.
Step 16: Gently push the original document into your printer’s ADF tray.
Step 17: Adjust the paper width guides so that they rest against the sides of the original.
Ensure that you don’t squeeze the original document with the guides.
Step 18: Plug the power cable into your printer.
Step 19: Turn on your printer.
Try scanning or copying a document.
If the issue is not resolved, do the task below.
2. Reset your printer – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To reset your printer, follow the steps we shared under the “Reset HP LaserJet Pro, Ultra M130 – M134 Printers” section of this article.
After resetting your printer, try scanning or copying a document.
If the issue is not resolved, you need to service your printer.
To service your printer, follow the instructions we shared under the “How to Service HP LaserJet Pro, Ultra M130 – M134 Printers” section of this article.
Er/04, Er/05, or Er/06 is Displayed and Blinking Attention Light – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
This error message and HP printer warning light pattern shows that a paper jam has occurred. Therefore, you need to clear the paper jam to resolve the problem.
Do the following solutions to fix this error.
1. Find Jammed Paper in HP LaserJet Pro, Ultra M130 – M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
We will guide you on how to find and clear jammed paper from different areas of your printer.
How to Clear Jammed Paper from Input Tray of HP LaserJet Pro, Ultra M130 – M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To clear jammed paper from your printer’s input tray, do the following steps:
Step 1: Take out loose paper from your printer’s input tray.
Step 2: Pull out the jammed paper you might find from your printer’s input tray using both hands.
Step 3: Load your printer’s input tray with paper.
Try printing a document.
If the issue is not resolved, check the next printer area for jammed paper.
How to Clear Jammed Paper from ADF of HP LaserJet Pro, Ultra M130 – M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To clear jammed paper from your printer’s ADF, do the following steps:
Step 1: Turn off your printer.
Step 2: Pull out the visible jammed paper from your printer’s ADF tray with both hands.
Step 3: Open your printer’s ADF cover.
Step 4: Pull out the jammed paper from within the ADF with both hands.
Step 5: Close your printer’s ADF cover.
Step 6: Turn on your printer.
Try printing a document.
If the issue is not resolved, check the next printer area for jammed paper.
How to Clear Jammed Paper from Toner Cartridge Area of HP LaserJet Pro, Ultra M130 – M134 Printers
To clear jammed paper from your printer’s toner cartridge area, do the following steps:
Step 1: Turn off your printer.
Step 2: Remove the power cable from the power source or wall outlet.
Step 3: Lift your printer’s scanner assembly.
Step 4: Open your printer’s top cover.
Step 5: Take out the toner cartridge from your printer.
Step 6: Take out the imaging drum from your printer.
Step 7: Pull out jammed paper with both hands from your printer’s toner cartridge area.
Step 8: Place the imaging drum in a way that it aligns with the track within your printer.
Step 9: Push the imaging drum slowly and gently into your printer and ensure that it is properly seated within your printer.
Step 10: Place the toner cartridge in a way that it aligns with the track within your printer.
Step 11: Push the toner cartridge slowly and gently into your printer and ensure that it is properly seated within your printer.
Step 12: Close your printer’s top cover.
Step 13: Lower your printer’s scanner assembly.
Step 14: Plug the power cable into an electrical wall outlet.
Step 15: Turn on your printer.
Try printing a document.
If the issue is not resolved, check the next printer area for jammed paper.
How to Clear Jammed Paper from Output Bin of HP LaserJet Pro, Ultra M130 – M134 Printers
To clear jammed paper from your printer’s output bin, do the following steps:
Step 1: Pull out the jammed paper with both hands from your printer’s output bin area.
Tip: If the jammed paper is difficult to reach, lift your printer’s scanner assembly.
Step 2: Try printing a document.
If the issue is not resolved, do the next solution.
2. Reset your printer
To reset your printer, follow the steps we shared under the “Reset HP LaserJet Pro, Ultra M130 – M134 Printers” section of this article.
After resetting your printer, check if the issue is resolved.
If the issue is not resolved, try to print a document again.
If the issue persists, then you need to service your printer.
To service your printer, follow the instructions we shared under the “How to Service HP LaserJet Pro, Ultra M130 – M134 Printers” section of this article.
Er/07 is Displayed and Blinking Supplies and Attention Lights – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
This error message and HP printer warning light pattern shows that the imaging drum or toner cartridge is installed incorrectly or missing.
To resolve this error, do the following solutions in the given order.
1. Remove and then Reinstall Toner Cartridge in HP LaserJet Pro, Ultra M130 – M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
How to Remove and then Reinstall Toner Cartridge in HP LaserJet Pro M130 – M132 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To remove and then reinstall the toner cartridge in your printer, follow the steps below:
Step 1: Lift your printer’s scanner assembly.
Step 2: Open your printer’s top cover.
Step 3: Take out the toner cartridge from your printer.
Step 4: Reinstall the cartridge into your printer and ensure that it is seated correctly.
Step 5: Close your printer’s top cover.
Step 6: Lower your printer’s scanner assembly.
How to Remove and then Reinstall Toner Cartridge in HP LaserJet Ultra M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To remove and then reinstall the toner cartridge in your printer, follow the steps below:
Step 1: Lift your printer’s scanner assembly.
Step 2: Open your printer’s top cover.
Step 3: Locate the toner cartridge within your printer and then rotate it so that it is in the unlock position.
Step 4: Take out the toner cartridge from your printer.
Step 5: Reinstall the cartridge into your printer and ensure that it is seated correctly.
Step 6: Rotate the toner cartridge so that it is in the lock position.
Step 7: Close your printer’s top cover.
Step 8: Lower your printer’s scanner assembly.
After removing and then reinstalling the toner cartridge into your printer, check if the error is resolved.
If the error is resolved, stop troubleshooting.
If the error is unresolved, do the next solution.
We recommend that you read this article: HP Printer Warning [Detailed Guide] to learn about other HP printer warnings that you might encounter when using your HP printer.
2. Remove and then Reinstall Imaging Drum in HP LaserJet Pro, Ultra M130 – M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
How to Remove and then Reinstall Imaging Drum in HP LaserJet Pro M130 – M132 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To remove and then reinstall the imaging drum in your printer, follow the steps below:
Step 1: Lift your printer’s scanner assembly.
Step 2: Open your printer’s top cover.
Step 3: Take out the toner cartridge from your printer.
Step 4: Take out the imaging drum from your printer.
Step 5: Reinstall the imaging drum into your printer and ensure that it is seated correctly.
Step 6: Reinstall the cartridge into your printer and ensure that it is seated correctly.
Step 7: Close your printer’s top cover.
Step 8: Lower your printer’s scanner assembly.
How to Remove and then Reinstall Imaging Drum in HP LaserJet Ultra M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To remove and then reinstall the imaging drum in your printer, follow the steps below:
Step 1: Lift your printer’s scanner assembly.
Step 2: Open your printer’s top cover.
Step 3: Locate the toner cartridge within your printer and then rotate it so that it is in the unlock position.
Step 4: Take out the toner cartridge from your printer.
Step 5: Take out the imaging drum from your printer.
Step 6: Reinstall the imaging drum into your printer and ensure that it is seated correctly.
Step 7: Reinstall the cartridge into your printer and ensure that it is seated correctly.
Step 8: Rotate the toner cartridge so that it is in the lock position.
Step 9: Close your printer’s top cover.
Step 10: Lower your printer’s scanner assembly.
After removing and then reinstalling the imaging drum into your printer, check if the error is resolved.
If the error is resolved, stop troubleshooting.
If the error is unresolved, do the next solution.
3. Replace the Toner Cartridge in HP LaserJet Pro, Ultra M130 – M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
How to Replace the Toner Cartridge in HP LaserJet Pro M130 – M132 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To replace the toner cartridge in your printer, follow the steps below:
Step 1: Lift your printer’s scanner assembly.
Step 2: Open your printer’s top cover.
Step 3: Take out the toner cartridge from your printer.
Step 4: Recycle the old cartridge.
Step 5: Take out the new cartridge from its packaging box and shell.
Step 6: Align the cartridge with the cartridge tracks within your printer.
Step 7: Push the cartridge into your printer and ensure that it is seated correctly.
Step 8: Close your printer’s top cover.
Step 9: Lower your printer’s scanner assembly.
How to Replace the Toner Cartridge in HP LaserJet Ultra M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To replace the toner cartridge in your printer, follow the steps below:
Step 1: Lift your printer’s scanner assembly.
Step 2: Open your printer’s top cover.
Step 3: Locate the toner cartridge within your printer and then rotate it so that it is in the unlock position.
Step 4: Take out the toner cartridge from your printer.
Step 5: Recycle the old cartridge.
Step 6: Take out the new cartridge from its packaging box and protective bag.
Step 7: Locate the arrow on the cartridge and align it with the unlock icon on the imaging drum within your printer.
Step 8: Push the cartridge into your printer and ensure that it is seated correctly.
Step 9: Rotate the toner cartridge so that it is in the lock position.
Step 10: Close your printer’s top cover.
Step 11: Lower your printer’s scanner assembly.
After replacing the toner cartridge, print a document to check if the error is resolved.
If the error is resolved, stop troubleshooting.
If the error is unresolved, do the next solution.
4. Replace the Imaging Drum in HP LaserJet Pro, Ultra M130 – M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
How to Replace the Imaging Drum in HP LaserJet Pro M130 – M132 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To replace the imaging drum in your printer, follow the steps below:
Step 1: Lift your printer’s scanner assembly.
Step 2: Open your printer’s top cover.
Step 3: Take out the toner cartridge from your printer.
Step 4: Take out the imaging drum from your printer.
Step 5: Recycle the old imaging drum.
Step 6: Take out the new imaging drum from its packaging.
Caution: Ensure that you don’t touch the imaging drum’s green roller. If your fingerprints get on this part, it can reduce the quality of your print jobs.
Step 7: Place the imaging drum in a way that it aligns with the tracks within your printer.
Step 8: Push the imaging drum into your printer and ensure that it is seated correctly.
Step 9: Align the cartridge with the cartridge tracks within your printer.
Step 10: Push the cartridge into your printer and ensure that it is seated correctly.
Step 11: Close your printer’s top cover.
Step 12: Lower your printer’s scanner assembly.
How to Replace the Imaging Drum in HP LaserJet Ultra M134 Printers – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To replace the imaging drum in your printer, follow the steps below:
Step 1: Lift your printer’s scanner assembly.
Step 2: Open your printer’s top cover.
Step 3: Locate the toner cartridge within your printer and then rotate it so that it is in the unlock position.
Step 4: Take out the toner cartridge from your printer.
Step 5: Take out the imaging drum from your printer.
Step 6: Recycle the old imaging drum.
Step 7: Take out the new imaging drum from its packaging.
Caution: Ensure that you don’t touch the imaging drum’s green roller. If your fingerprints get on this part, it can reduce the quality of your print jobs.
Step 8: Place the imaging drum in a way that it aligns with the tracks within your printer.
Step 9: Push the imaging drum into your printer and ensure that it is seated correctly.
Step 10: Align the cartridge with the cartridge tracks within your printer.
Step 11: Push the cartridge into your printer and ensure that it is seated correctly.
Step 12: Rotate the toner cartridge so that it is in the lock position.
Step 13: Close your printer’s top cover.
Step 14: Lower your printer’s scanner assembly.
After replacing the imaging drum, print a document to check if the error is resolved.
If the error is resolved, stop troubleshooting.
If the error is unresolved, then you need to service your printer.
Er/08, Er/09, or Er/10 is Displayed, and Blinking Supplies and Attention Lights – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
If the attention light is blinking and Er/08 is displayed, it means that the toner level in the cartridge is very low.
If the attention light is blinking and Er/09 is displayed, it means that the imaging drum is very low.
If the attention light is blinking and Er/10 is displayed, it means that the imaging drum and toner cartridge are very low.
- For M132a and M130a printers: Press your printer’s “Start Copy” button to resume printing without changing the cartridge or drum. However, you need to replace the affected supply when the print quality is no longer acceptable.
- For the M134a printer: Replace the affected supply to resume printing.
Below is a more detailed troubleshooting process to resolve the problem:
1. Replace the Affected Toner Cartridge – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To replace the affected toner cartridge, follow the steps we shared under the “How to Replace the Toner Cartridge in HP LaserJet Pro M130 – M132 Printers” section for HP LaserJet Pro M130 – M132 printers or the “How to Replace the Toner Cartridge in HP LaserJet Ultra M134 Printers” section for HP LaserJet Ultra M134 printer.
After replacing the toner cartridge, check if the problem is resolved.
If the problem persists, do the troubleshooting step below.
2. Replace the Imaging Drum – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To replace the imaging drum, follow the steps we shared under the “How to Replace the Imaging Drum in HP LaserJet Pro M130 – M132 Printers” section for HP LaserJet Pro M130 – M132 printers or the “How to Replace the Imaging Drum in HP LaserJet Ultra M134 Printers” section HP LaserJet Ultra M134 printer.
After replacing the imaging drum, check if the problem is resolved.
If the problem persists, service your HP printer.
Er/11 to Er/19 is Displayed and Blinking Supplies and Attention Lights – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
The following are the reasons your printer might display any of these error codes:
i. Er/11, Er/14, or Er/17: This is an indication that the toner cartridge installed into your printer is not compatible, has been protected after being used in a different printer, or is unauthorized.
ii. Er/12, Er/15, or Er/18: The imaging drum installed into your printer is not compatible, has been protected after being used in a different printer or is unauthorized.
iii. Er/ 13, Er/16, or Er/19: The toner cartridge and the imaging drum are not compatible, have been protected after being used in a different printer, or are unauthorized.
To resolve the problem, you need to replace the affected printer supplies.
Below is a more detailed troubleshooting process to resolve the problem:
1. Replace the Affected Toner Cartridge – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To replace the affected toner cartridge, follow the steps we shared under the “How to Replace the Toner Cartridge in HP LaserJet Pro M130 – M132 Printers” section for HP LaserJet Pro M130 – M132 printers or the “How to Replace the Toner Cartridge in HP LaserJet Ultra M134 Printers” section for HP LaserJet Ultra M134 printer.
After replacing the toner cartridge, check if the problem is resolved.
If the problem persists, do the troubleshooting step below.
2. Replace the Affected Imaging Drum – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To replace the imaging drum, follow the steps we shared under the “How to Replace the Imaging Drum in HP LaserJet Pro M130 – M132 Printers” section for HP LaserJet Pro M130 – M132 printers or the “How to Replace the Imaging Drum in HP LaserJet Ultra M134 Printers” section HP LaserJet Ultra M134 printer.
After replacing the imaging drum, check if the problem is resolved.
If the problem persists, service your HP printer.
Er/20 is Displayed and Blinking Supplies and Attention Lights – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
This error and warning light pattern are an indication that the toner cartridge sensors have encountered an error. To resolve this error, you need to replace your printer’s toner cartridge.
To replace your printer’s toner cartridge, follow the steps we shared under the “How to Replace the Toner Cartridge in HP LaserJet Pro M130 – M132 Printers” section for HP LaserJet Pro M130 – M132 printers or the “How to Replace the Toner Cartridge in HP LaserJet Ultra M134 Printers” section for HP LaserJet Ultra M134 printer.
After replacing the toner cartridge, check if the problem is resolved.
If the problem persists, service your printer.
Er/25 is Displayed and Blinking Attention Light – HP Printer Warning Light on HP LaserJet Pro M130 and Ultra M134 Printers
When this error message is displayed and the attention light is blinking, it means that you loaded the wrong paper size for the current print job into your printer.
To fix this error, try the following solutions.
1. Load your Printer with the Right Paper Size – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To load your printer with the right paper size, do the following steps:
Step 1: Lift your printer’s dust cover.
Step 2: Take out the stack of paper from your printer’s input tray.
Step 3: Get a stack of the right paper size for the current print job.
Step 4: Examine the stack of paper and confirm that the condition of each paper sheet is good. If you find any sheet that is torn, wrinkled, or bent, remove it from the paper stack.
Step 5: Hold the stack of paper in both hands, and then flex it in a way that a “U” shape is formed.
Step 6: Flex the stack of paper in the other direction still forming a “U” shape.
Flexing the stack of paper in this manner can loosen the individual sheets within the stack.
Step 7: Load the paper stack with the print side face up into your printer’s input tray.
Note: Do not load more than 150 paper sheets into the input tray. Ensure that the print side faces up while the top edge goes into the printer. if the paper you are loading is pre-punched, the side with holes should be at the tray’s left side when you load it in.
Step 8: Push the paper stack into your printer’s input tray.
Step 9: Adjust the paper width and length guides to rest against the paper stack.
Step 10: Lightly press the side of the printer’s dust cover inwards.
Step 11: Lower the printer’s dust cover.
Caution: Don’t lower the printer’s dust cover if you are not pressing the sides inwards. Doing otherwise might get the printer or the dust cover damaged.
Note: Before you print or copy, you need to choose the correct paper type and paper size settings from your computer or printer’s control panel.
Try printing a document.
If the issue is not resolved, do the solution below.
2. Resume Printing – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
You can resume printing even with the current paper size. To do this, press your printer’s “Start Copy” button.
Bear in mind that the print quality might be affected since the paper is not the right size for the current print job.
Er/30 to Er/79 is Displayed and Turned-on Attention and Ready Lights – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
When your printer’s attention and ready lights are turned on and you see any of these error messages: Er/30, Er/49, Er/50, Er/51, Er/52, Er/53, Er/54, Er/55, Er/56, Er/57, Er/58, Er/59, Er/60 or Er/79, it means that your printer has entered an error state.
To resolve this error, do the following solutions.
1. Reset your printer – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To reset your printer, follow the steps we shared under the “Reset HP LaserJet Pro, Ultra M130 – M134 Printers” section of this article.
After resetting your printer, check if the error is resolved.
If the error is resolved, you can stop troubleshooting.
If the error persists, do the next solution.
2. Plug HP LaserJet Pro, Ultra M130 – M134 Printers Directly into a Wall Outlet – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
Follow the steps below to plug your printer directly into a wall outlet:
Step 1: Remove the printer’s power cable from your HP printer.
Step 2: Remove the printer’s power cable from its connected power source (surge protectors, power strips, etc.)
Step 3: Connect the printer’s power cable directly to a wall outlet.
Step 4: Plug the power cable into your HP printer.
Step 5: Turn on your HP printer.
Check if the error is resolved.
If the error is resolved, you can stop troubleshooting.
If the error persists, service your HP printer.
Er/81 is Displayed and Blinking Attention Light – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
This is an indication that the firmware loaded in your printer is incorrect.
To install the correct firmware on your HP printer, click this link: Update your HP Printer Firmware – HP Printer is Slow, and then use any of the methods we shared to install your HP printer firmware.
Go/01 is Displayed and Blinking Attention Light – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
This is an indication that your printer is operating in manual paper feed mode.
Therefore, when this happens, do the following:
i. Load your printer’s input tray with the correct paper size for the current print job.
ii. Press your printer’s “Start Copy” button to resume printing.
Go/02 is Displayed and Blinking Attention Light – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
This is an indication that your printer is busy processing a manual duplexing print job that requires your assistance to complete the job.
Therefore, to complete the print job, do the following:
i. Take out the printed pages from your printer’s output tray.
ii. Load the printed pages into your printer’s input tray with the side that has been printed on facing down while the top edge of the pages goes into your printer.
ii. Press your printer’s “Start Copy” button to resume printing on the other side of the pages.
This happens when your printer is either turned off, or the power supply has an issue.
To resolve this issue, do the following solutions.
All the Printer Lights are Turned off, and the Printer is not Responding – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
This happens when your printer is either turned off, or the power supply has an issue.
To resolve this issue, do the following solutions.
1. Turn on your printer – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
Press your printer’s power button to turn on your device.
Check if the problem is resolved.
If your printer is turned on and responding, then the problem is resolved. Therefore, you can stop troubleshooting.
If the problem is not resolved, do the solution below.
2. Ensure that your printer is Properly Plugged in – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To ensure that your printer is properly plugged in, follow the steps below:
Step 1: Check the back of your printer and ensure that the power cable is properly plugged into your printer. If it isn’t, plug it in properly.
Step 2: Check and confirm that the power cable is properly plugged into the electrical wall outlet. If it isn’t, plug it in properly.
Step 3: Turn on your HP printer by pressing its power button.
If it turns on, then the problem has been resolved. Therefore, you can stop troubleshooting.
However, it if fails to turn on, do the solution below.
3. Ensure that the Wall Outlet Works – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
To ensure that the wall outlet works, follow the steps below:
Step 1: Remove the printer’s power cable from the wall outlet.
Step 2: Plug a different appliance into the wall outlet.
If the appliance doesn’t turn on, then it means that the outlet is not working. In such a case, you need to connect your HP printer to a different but working outlet.
On the other hand, if the appliance turns on, then the outlet is working. Therefore, continue with the solution below.
4. Ensure that you are Using a Compatible Power Supply – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
When we say “power supply,” we are talking about the power cable/cord and power module. If the power supply isn’t compatible with your printer, it can lead to all kinds of issues.
Note: To ensure that you are using a compatible power supply, it is recommended that you use the power supply that came with your HP printer.
To confirm that you are using a compatible power supply, follow the steps below:
Step 1: Ensure that the specification for the amperage and voltage shown on the power supply is the same as that shown on the body of your printer.
Step 2: Once you get a match for the amperage and voltage, ensure that the power supply connector’s size and shape match that on your HP printer.
Warning: Don’t force a connector that isn’t the same size or shape into your HP printer to prevent damage.
If the power supply is incompatible, get a new compatible power supply.
If the power supply is compatible, but your printer still won’t turn on, continue with the solution below.
5. Use another Power Cable to Test your Printer’s Power – HP Printer Warning Lights on HP LaserJet Pro M130 and Ultra M134 Printers
If there is another compatible power cable around, plug it into your printer and a wall outlet.
If using another power cable causes your printer to turn on, then the initial power cable is faulty. Therefore, you need to get a replacement power cable.
On the other hand, if using another power cable doesn’t cause your printer to turn on, then you need to service your HP printer.
- BIG RESULTS, SMALL FOOTPRINT – Print consistently high-quality documents with the HP LaserJet Pro M501dn, a monochrome laser printer designed to provide impressive speed and performance
Prices pulled from the Amazon Product Advertising API on:
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on [relevant Amazon Site(s), as applicable] at the time of purchase will apply to the purchase of this product.